Just how do you really feel in regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Mounting a bathtub isn't precisely brain surgery, but it does require solid plumbing, carpentry, and in some cases, tiling skills. Changing an old bath tub with a new one is also a reasonably hard project. If the old tub is easily obtainable, the task can move rapidly; if you have to open up a wall surface to get rid of the old bathtub and position the brand-new bath tub, the task is much harder. In either situation, the project is within a home handyman's skills, although you will need an assistant to vacate the old bathtub and embeded in the brand-new one. See to it you have qualified on your own for the work and are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is far better to consider utilizing one before you begin. Possibilities are you may need an expert plumber to make tube links.
This write-up will assist you mount a brand-new bath tub in your bathroom if you have already purchased a brand-new bathtub and also don't need to alter the plan of your previous water pipelines.
Your devices as well as product checklist ought to make up the following:
Getting ready for the Setup
First of all, the supporting framework supplied with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to stop strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its final position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is disconnect the supply of water. After doing so, activate the faucets to drain any kind of water staying in the system. The process of removing the existing faucets can be quite troublesome because of the restricted accessibility that is typically the case.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the remaining water that will certainly come from the pipelines. When the supply pipes have been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Prior to carrying on to fit the new faucets, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Making use of the two wood boards under its feet, put the bathtub in the needed position. The wood boards are useful in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four little factors.
The following goal is to ensure that the tub is leveled all round. This can be attained by inspecting the level and changing the feet on the bath tub until the level reviews level.
To mount taps, fit all-time low of the outermost flexible faucet connector to the proper supply pipeline by making a compression join; then do the very same for the various other faucet.
Activate the water supply as well as examine all joints as well as brand-new pipework for leakages and tighten them if needed. Fill the bathtub as well as additionally check the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, deal with the bath paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has actually been used a minimum of when as this will settle it right into its final setting.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will require a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and the other end offers a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin ensuring that the washers are in location in between the tap and the sink. Protect the faucet in place with the maker given backnut. Once the tap is safely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former kind must be attached to the faucet finishes first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall between the bath as well as the tiling, resulting in problems with moisture as well as possible leaks to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and also installations. They are offered in tubes as well as cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to enable the activity experienced when the bathtub remains in usage. The sealant can break fairly early if you do not take into account this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly available on the market. It is suggested to fit the ceramic tiles making use of waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very enthusiastic about Tools You Need to Install a New Bathtub and I hope you enjoyed reading my blog entry. I beg you take the opportunity to share this blog entry if you liked it. Thanks for your time. Please check up our blog back soon.
Free Estimates